Fill in the dropdown with the right value to stop the lrf_loading after loading a certain number (eg, num_limit) of data packets.

if (reset) begin
ready

Question

Fill in the dropdown with the right value to stop the lrf_loading after loading a certain number (eg, num_limit) of data packets.

if (reset) begin
    ready <= XX;
    ...
end
else begin
    if (lrf_load && ready) begin
        load_start <= 1;  mem_rd <= 1; ready <= XX;
    else if (load_start) begin
        if (load_cnt == num_limit) begin
            mem_rd   <= 0;
            acc_done <= 1;
            load_start <= 0 ;
        end
        else  
            load_cnt <= load_cnt + 1;
    end
    ...
end

BlackTom AI · Accepted Answer

The task presents a small Verilog-like snippet that controls a loading sequence and asks for the value to fill in a dropdown to stop lrf_loading after a certain number of data packets (num_limit).

First, restating the key behavior from the code helps: when reset is not active, the code checks if lrf_load && ready is true, and if so, it begins a loading sequence by setting load_start to 1, mem_rd to 1, and assigns ready to some value (XX). While load_start is active, it checks if load_cnt has reached num_limit; if so, it disables mem_rd, signals acc_done, and clears load_start. If the limit has not been reached, it increments load_cnt. This structure suggests that ready acts as a gate or handshake flag indicating whether a new load cycle can begin or whether the system is prepared to accept another load request.

Option analysis without explicit alternatives (since answer_options are empty):

- Conceptually, ready is used as a control signal that governs when lrf_load can initiate a new loading cycle. When the system has reached the desired number of packets (load_cnt == num_limit), the code sets load_start to 0 and asserts acc_done, effectively terminating the current load operation. To ensure the logic stops initiating new loads after the limit is reached, the ready signal should be in the non-ready state (i.e., 0) at that moment, so that the condition lrf_load && ready cannot be true again until the system is prepared to load more data.

- Given the provided answer array includes "0" and the typical convention is that ready = 0 means not ready (cannot start a new load) and ready = 1 means ready (can start a new load), assigning ready = 0 aligns with stopping further loading once the limit is reached. The code path that sets load_start and mem_rd is only triggered when lrf_load && ready is true; once load_start is cleared and acc_done is issued, the system should not immediately re-enter a new load unless some external event sets ready back to 1. Setting ready to 0 in the completion path prevents an immediate retriggering.

- What would be incorrect or misleading: choosing ready = 1 (if that were an option) would imply the module remains ready to accept another load request, which could cause lrf_load && ready to re-fire and potentially exceed the intended num_limit if load_cnt is not properly reset or guarded elsewhere. This would defeat the purpose of stopping after the specified number of packets.

- About the missing dropdown options: since there are no alternative values shown, it's important to understand that the intended fill likely corresponds to a binary control where 0 indicates not ready and 1 indicates ready. The logic flow during the completion phase supports setting ready to 0 to prevent immediate re-entry into the load sequence and to clearly indicate that the system has completed the requested number of packets.

In summary, the most sensible value to place in the dropdown to stop lrf_loading after reaching num_limit is 0, representing a not-ready state that prevents further loading until some other condition externally reasserts readiness. If there were alternative options, the correct choice would be the one that clearly deasserts readiness after completion of the load sequence, rather than reasserting readiness inadvertently.

ECE260B_WI25_A00 Mock ECE260B Final Quiz

查看解析

登录即可查看完整答案

类似问题

In a consumer society, many adults channel creativity into buying things

Economic stress and unpredictable times have resulted in a booming industry for self-help products

People born without creativity never can develop it

A product has a selling price of $20, a contribution margin ratio of 40% and fixed cost of $120,000. To make a profit of $30,000. The number of units that must be sold is: Type the number without $ and a comma. Eg: 20000

Which of the following statement regarding cost is correct:

Under the assumptions used in cost-volume-profit analysis, as the activity increases:

The CVP and break-even analysis are supported by a range of important assumptions. Which of the following is not an assumption of the CVP:

更多留学生实用工具

考试浏览器助手

风格化写作助手

论文查重助手

文献引用助手

课堂转译助手

课堂笔记助手

Quiz搜索助手

学校历年真题

智能刷题助手

智能匹配练习

希望你的学习变得更简单